What Lumber Is Used to Frame Houses in BC? Framing Lumber Grades and SPF Explained
October 13, 2026 | Category: Framing Resources
S-P-F is the species group BC’s interior mills produce, written on the end of the board as three letters, and kiln-dried SPF lumber is used as a structural framing material in all types of residential building. The coast grows a different set of woods, sold together under the commercial name hem-fir. That is why a set of structural drawings names a species group rather than just saying lumber.
On a custom home framing project, the species group and the framing lumber grades are fixed on the drawings and in the order, weeks before a banded package lands on the lot. When what arrives does not match what was drawn, the frame stops, and the people who can fix it are not standing on your lot.
What S-P-F Means, and Why BC Framing Lumber Arrives as a Group
Softwood is not bought or designed one species at a time. Mills do not need to sort spruce from pine from fir, because woods that behave alike are bundled into a commercial group. The group is what carries a name, a stamp mark and a set of strength numbers.
The Three Woods Sold as S-P-F
S-P-F stands for spruce-pine-fir, and in British Columbia it is three woods sold together: lodgepole pine, interior spruce and subalpine fir. Lodgepole pine is the most abundant tree species in British Columbia, which is the supply-side reason the group exists here at all.
White and Engelmann spruce grow throughout the interior east of the Coast Range, and subalpine fir grows through most of the interior from mid to high elevations. None of those three is a coastal tree.
The Coast Grows a Different Group, and Your Job Can Draw on Both
Western hemlock, the most plentiful species on BC’s coast, is sold together with amabilis fir under the commercial name hem-fir. The coast has its own group, and a Lower Mainland yard can be served from either side of the Coast Range.
The group is the unit of substitution. Swapping a stick of pine for a stick of spruce inside S-P-F changes nothing. Swapping S-P-F for hem-fir changes the numbers your designer worked from, and that is the whole reason a drawing names a group instead of a tree.
What Framing Lumber Grades Actually Measure

A lumber grade is a minimum standard describing the characteristics allowed in a piece of lumber. Each piece is assigned a grade based on its quality, using a rule that considers the intended use of the piece, its size, quality and, in some cases, its species.
So a grade is a ceiling on strength-reducing defects, not a description of looks. A knotty No.2 joist can be exactly right for the span it was sized for, while a clean board with a steep grain slope is the weaker piece.
Canadian lumber is graded to the National Lumber Grades Authority’s Standard Grading Rules for Canadian Lumber. Those rules are updated on their own schedule, so a designer works from the edition the code points at.
The Four Grade Families, and What Each One Frames
Sawn dimension lumber is not graded on one ladder. It comes in four families, set by what the piece is for and how wide it is. Whether a member is sawn lumber or an engineered product is a separate decision, covered in our piece on engineered lumber and dimensional lumber.
| Grade family | Grades in it | What it is for |
| Structural Light Framing | Select Structural, No.1, No.2, No.3 | Pieces 2×2 through 4×4 where high-strength design values are required |
| Structural Joists and Planks | Select Structural, No.1, No.2, No.3 | Engineering applications in lumber 5 inches and wider, 2×5 through 4×18: floor and ceiling joists, rafters, headers, small beams, trusses |
| Light Framing | Construction, Standard, Utility | Basic framing lumber in 2×2 through 4×4 sizes: wall framing, sills, plates, cripples, blocking |
| Stud | Stud | Vertical use in load bearing walls. The only grade in its family. |
The Grades for Pieces Carrying Engineered Loads
Two of the four families are for pieces carrying engineered loads. Structural Light Framing covers 2×2 through 4×4 where high-strength design values are required. Structural Joists and Planks covers 2×5 through 4×18, for engineering applications in lumber 5 inches and wider: floor and ceiling joists, rafters, headers, small beams and trusses.
Both run the same ladder, Select Structural, No.1, No.2 and No.3. The ladder repeating at a different width is why two specifications can both say No.2 and mean different products. The names are common across North America.
Light Framing and Stud Grade: Plates, Blocking and Walls
Light Framing covers the same 2×2 through 4×4 sizes and is the basic framing lumber in most light-frame construction: wall framing, sills, plates, cripples and blocking, graded Construction, Standard and Utility.
Stud is the odd one out: a single grade rather than a ladder of them, intended for vertical use in load bearing walls, which is the one job it has to do.
A stud and a joist are not better and worse versions of one product. A leftover joist is not an upgrade when it ends up as a plate.
What the Yard Calls It, and Why It Does Not Match the Drawing
In practice, Select Structural, #2 and better, and stud grades are the most common grades produced from BC’s SPF woods. That is yard language, not drawing language.
A delivery slip will often say No.2 and better. That is not a grade, it is a bundle, meaning No.2 or anything above it. In Canada, identical design values are given for No.1 and No.2 grade lumber, and those two grades differ mainly in appearance rather than strength, which is why a mill can ship them together. Design values are the strength and stiffness numbers a designer works from.
How to Read the Grade Stamp on Your Lumber

The stamp is the whole promise in one mark, and it is the part of this subject you can check yourself with no tools at all. On BC lumber it often carries the trademark of the Pacific Lumber Inspection Bureau, an accredited grading agency named for the Pacific region.
The Five Marks on a Grade Stamp
A legitimate stamp carries five things, each answering a different question.
- Agency trademark: who stands behind the piece.
- Mill identity: a name or mill number.
- Grade: a name, number or abbreviation.
- Species: the species or species combination.
- Seasoning: how dry it was when it was surfaced.
Lumber should be identified by a grade stamp applied under the supervision of an accredited grading agency. The Canadian Lumber Standards Accreditation Board makes sure structural lumber made in or imported into Canada is accurately graded and identified, and that accreditation work is referenced in the national and provincial building codes across Canada. It also has to be readable when your frame is checked, which is part of what a framing rough-in inspection covers.
The Seasoning Mark: S-DRY, KD and S-GRN
Framing lumber is dried before it leaves the mill, and the stamp says how dry it was when the piece was surfaced.
- S-DRY or KD: surfaced at 19% maximum moisture content.
- MC15 or KD15: surfaced at 15% maximum.
- S-GRN: surfaced green, which is to say unseasoned.
Lumber is typically kiln dried to 19% or less, which reduces swelling and shrinkage and increases resistance to decay and insect attack. On this coast, you want the mark that says the wood left the mill dry. Keeping it dry on the lot is another subject, covered in our piece on keeping lumber dry once it is on site.
When the Stamp Carries Numbers Instead of a Grade Name
Visual grades are set by assessing each piece for strength-reducing characteristics such as knots and slope of grain. Machine stress rated lumber is different: every piece is tested to measure its stiffness, and the stamp carries numbers for strength and stiffness instead of a grade name. The short form is MSR.
Most homeowners meet it as roof-truss lumber, where the boards arrive stamped with numbers nobody recognizes and nothing is wrong. The truss supplier chose machine graded stock because the design was tight, and that choice was made in a shop, not on your lot.
Why a Species or Grade Change Is Not a Field Decision

The strength and stiffness numbers a designer sizes a joist or a rafter with belong to one species group and one grade. Change either and the numbers change, which is why the drawings name both, and why those values are written for qualified designers.
Nobody on site can authorize a change either. Certified mill graders cannot certify or stamp lumber for homeowners or builders, and a mill grader can only grade at the mill they were certified for. A short delivery filled out with the equivalent is a design change made by a dispatcher, and it belongs to whoever signed the drawings.
Where the Frame Lands on Concrete
The lowest piece of wood in the building gets treated differently from everything above it. Where framing lands on concrete, the wood is either pressure-treated for that exposure or it is separated from the concrete by a barrier, and your drawings say which.
Every cut and every drilled hole in treated wood should get an end-cut treatment as the work goes, because cutting exposes wood the preservative never reached. Invisible once the plate is down, and exactly where decay starts. That plate is also the first step in how a custom home frame goes up from the sill plate.
Which Rulebook Your Lower Mainland Project Follows

Part 9 of the BC Building Code governs a house like yours, and the species group and grade on your drawings come out of it. The BC Building Code 2024 has been in effect since 8 March 2024, and most of it is based on the National Building Code of Canada 2020 with some BC-specific changes.
The BC Building Code does not apply in the City of Vancouver, which has its own building by-law, so a house inside the city limits is built to a different rulebook from one in Burnaby, Richmond or Surrey. Ask which one your project is being designed to.
Getting the Right Species and Grade on Your Build
By the time lumber is on the lot, the species group and the grade were settled weeks earlier. A residential framing company earns its place on the job by checking the package against the drawings before anything gets nailed, and by knowing who to call when the two do not agree.
Anvil West has been owner-led since 2013, and Red Seal carpenters lead our work in the field. Forming and framing come from one crew, so the wood-to-concrete line is not a handoff between trades. If you have drawings in front of you, get in touch with our Vancouver team and we will read them with you.
Frequently Asked Questions
What Does S-P-F Stand for on Framing Lumber?
Spruce-pine-fir, a commercial group rather than one species. In British Columbia it is lodgepole pine, interior spruce and subalpine fir, sold together because they behave alike.
Why Do My Drawings Name a Species Group Instead of Just Saying Lumber?
Because the strength and stiffness numbers your frame was sized with belong to one species group and one grade. BC’s coast sells a different group as hem-fir, so naming the group records which numbers were used.
What Is the Difference Between No.2 and Stud Grade Lumber?
Different families for different jobs. Stud is a single grade intended for vertical use in load bearing walls, while the Select Structural through No.3 ladder covers pieces carrying engineered loads.
What Does S-DRY Mean on a Grade Stamp?
That the piece was surfaced at 19% maximum moisture content. KD means the same, MC15 and KD15 mean 15% maximum, and S-GRN means surfaced green.
Can My Framer Substitute a Different Grade if the Yard Is Short?
Not on site. A mill grader can only grade at the mill they were certified for, and nobody can stamp lumber for a homeowner or builder, so the change goes back to whoever engineered the frame.
Why Do Some Roof Trusses Have Numbers Stamped on Them Instead of a Grade Name?
That lumber was machine graded. Each piece was tested for stiffness rather than sorted by eye, so the stamp carries numbers for strength and stiffness in place of a grade name.